Welcome to the Workshop 12 family. 🤘
Below is your step-by-step installation guide, designed to walk you through everything from wiring and setup to troubleshooting. Please follow each step carefully. If you run into an issue that isn't covered here, scroll to the bottom of the page to reach out via email, phone, or by booking a 1-on-1 video call.
STEP 1: Unboxing
What's in the box:
- SIM Card Tray
- LTE Antennas
- GPS Antenna
- 2 RCA’s Connections
- 2 Female USB Ports
- USB Connection for Reverse Camera Feed
- Main stereo harness
- Microphone
- BUZZER
- AM/FM radio wire
- Radio wire
Wiring Diagram
STEP 2.1: INSTALLATION (NON-NAVIGATION VERSION)
Before You Begin: Tools & Prep
-
Get basic trim tools (plastic pry tools), a screwdriver set, and a 10 mm socket.
1. Remove the factory dash screen.
- Carefully pry off the trim around the factory radio and center console using your plastic trim tools.
- Unscrew the mounting bolts and gently pull the OEM unit out.
- Disconnect all OEM harness connectors and antenna plugs from behind the dashboard.
- DO NOT DISCONNECT THE CD PLAYER
2. Transfer Factory Components
- Remove the original dash retaining clips from the OEM trim and transfer them onto the new unit.
- Carefully extract the factory triple gauges from the top of the original dash.
- Transfer and securely mount these gauges into your new Workshop 12 dash bezel.
3. Connect Workshop 12 Harness
- Take the Workshop 12 plug-and-play wiring harness:
- It should perfectly match the main factory plugs (no wire cutting or splicing needed).
- Connect the main harness into the vehicle's OEM connector that was originally plugged into the stock unit.
- Connect the GPS antenna, LTE/4G antennas, and the rest of the auxiliary wires (like USB or RCA inputs) you wish to use from the kit.
4. Test the Screen Functions
- Turn the vehicle on and allow the new screen to power up.
- Verify that the screen turns on correctly.
- If everything is functioning correctly, turn the vehicle off before completing the installation.
5. Mount the New Screen
- Once all harnesses and gauges are connected:
- Align the new 12.1" display with the dash opening.
- Push the trim piece back into place, ensuring the clips seat fully without applying excessive force.
- Please ensure no wires are pinched behind the dash while pushing in the new unit.
You can also follow the install video below just so you can have an even better understanding of this process ⬇️
STEP 2.2: INSTALLATION FULL NAVIGATION VERSION
You can also follow the install video below just so you can have an even better understanding of this process ⬇️
-
STEP 3: STEERING WHEEL CONTROL WIRING/PROGRAMING
- Key 1: Connects to the orange wire of the factory SWC harness.
- Key 2: Connects to the red/green wire of the factory SWC harness.
- Ground: Connects to the yellow/green wire of the factory SWC harness.
You can also follow the install video below just so you can have an even better understanding of this process ⬇️
-
STEP 4: NOT HEARING ANY AUDIO (FIX)
- Ensure all the wires are properly connected on the harness
- power on the unit
- Go to the settings app
- Go into sound settings and turn on the AMP ON/OFF setting
You can also follow the install video below just so you can have an even better understanding of this process ⬇️
-
STEP 5: COMPLETE SOFTWARE WALKTHROUGH
- Additional Resources for Below:
- How to change the time on your unit
- Sim-card tray
Reverse Camera Installation 350Z
- Need Extra Help? Book a 1-on-1 Video Call
- If you have an issue that hasn't been covered, or if you just prefer a guiding hand, you can schedule a live troubleshooting and setup session with a Workshop 12 technician.
- Book your 1-on-1 Video Call by clicking this link 👉 BOOK NOW
- Don't see a time that works?
- Simply email us at info@workshoptwelve.com with two preferred dates and times, and we’ll do our absolute best to accommodate your schedule.
- Contact us:
- info@workshoptwelve.com
- +1 226-774-8122
